One day I returned home only to find that our Sony Wega TV (Model KV34HS420) was no longer working. It would respond to the remote control and begin to start to turn on, but then it would make a clicking sound and turn itself off before a picture appeared on the screen. After that, the standby/timer LED would continue blinking 6 or 7 times. This blinking LED is a diagnostic code, but its description of the potential issue provided little value. After reading a few dozen postings on the issue, a pattern began to emerge that made me hopeful that I could repair it myself.

  • Details about SHINDENGEN MCZ3001DB Replaces - MCZ3001DA & MCZ3001D & 670581001 For Sony, Hitachi and other TV Repair - IN STOCK.
  • Details about SHINDENGEN MCZ3001DB Replaces - MCZ3001DA & MCZ3001D & 670581001 For Sony, Hitachi and other TV Repair - IN STOCK. SHINDENGEN MCZ3001DB Replaces - MCZ3001DA & MCZ3001D & 670581001. Item Information. Money back or replacement (buyer's choice) Buyer pays for return shipping.

We purchased this TV in 2005 while the jury was still out about which flat panel TV technology would eventually replace the tried-and-true CRT technology. Back then, the LCD and plasma flat panel displays still had viewing angle and reliability issues and cost 2 or 3 times as much as an equivalent-sized CRT model and so we just decided to replace our 15-year-old Sony CRT TV with a modern HD-capable CRT TV. I was hoping to get 15 years or more out of this $1500 investment before having to send it to the landfill. After all, this was a SONY, not some no-name brand that I’d expect to fail after only a few years. And tube TVs usually last a very long time. I have one in my basement I purchased in 1985 that is still working fine.

1PCS Audio Power IC SHINDENGEN DIP-18 MCZ3001D + 18P SOCKET 100% Genuine and New. $1.80 + $4.00 shipping. Picture Information. Opens image gallery.

This TV has excellent picture quality and no restrictions in viewing angle, and other than its size and weight, I found it much better than what was available with flat panel technologies at the time. Its speakers provide excellent sound quality, much nicer than the tinny sound produced by some of the razor-thin flat panels. It sits in a corner and therefore takes up no more room than an equivalent size flat panel display. So, after only 6 years, I was wondering whether it would need to be replaced or if I could fix it. After a fair amount of forum reading, I found that this 6 or 7 LED blink code was a rather common problem, along with a common solution, namely to replace the MCZ3001DB integrated circuits known as IC8002 and IC6501 on the ‘D’ board. This chip is functionally identical to earlier versions of it known as MCZ3001D or MCZ3001DA. The forums had many people describing their success at making the repair, but pictures of this procedure were non-existent, hence the reason for this blog posting. Also, the level of difficulty and amount of work involved was not clearly described, so I hope to explain and show what I did so the reader can determine whether it is within his or her skill level to attempt this repair.

This TV weighs 200 lbs. I didn’t want to have to move it from its stand. Fortunately, it was possible to remove the entire back shell simply by removing all of its screws and sliding it off. There are a lot of screws, about a dozen around the periphery of the TV along with several more on the back panel, but fortunately, it’s a one-person job although it wouldn’t hurt to have a helper because the shell, although fairly lightweight, is bulky. Removing the shell allows access to the ‘D’ board.

After removing about a 17 screws, the rear shell can be slipped off.

The ‘D’ board is the one shown in the picture below. I should mention that before removing the cover, you must unplug the TV and give it a few hours for the high voltages to dissipate so as to avoid shock hazards. It’s best to unplug it and wait overnight, since if the TV is not working so there’s no need for it to remain connected to power.

The 'D' board shown above is held in with about 8 screws.

It wasn’t clear how to remove the board, or if it would be necessary to undo all of the wiring connections. Some of the connectors were easy to remove, but the 3 high voltage wires that connect to the CRT did not have easy-to-unplug connections. I eventually figured out that I didn’t need to remove those wires at all. There are a number of connectors that need to be flipped upward to disconnect the ‘D’ board from an adjacent board. It wasn’t clear at first how they worked, but if you feel around for a flange you can pull them upward, they’ll unsnap and pivot up 90 degrees like a draw bridge. Two of the connectors had latches on them that require squeezing the lever to unlatch it before they will come out. I unplugged all the other cables I could find, removed about 8 screws, and the board came out far enough to let me rotate it into a position where I could access the bottom of the board. It was necessary to use a stubby screw driver to remove one screw that was far forward, hidden between two connectors, and just under the CRT. To make that easier, you will notice that there are two plastic hooks, one on each side of the tray that the boards are mounted to that you can unlatch which allows all the PC boards to slide back about 4 inches. That makes the front screw easier to access, although you’ll still need that stubby screwdriver. (I’ve since added images of the latch and the board slid back at the end of this article.) After you get all the screws out, the board is still held in by a few plastic clamps on the edge which you can bend back a little to release the board. The board was still tethered by the high voltage connections, but I was able to fix it ‘in place’, by turning it over like shown in the image below.

Bottom of Sony 'D' board shown rotated in repair position. Note, it's not necessary to disconnect the wire with the suction-cup-like insulator on it.

Unsoldering the two ICs is not difficult if you use a spring loaded solder sucker like the one shown below. Do not waste your time trying to use solder wick or a bulb-type solder sucker for desoldering the chips. Search for YouTube videos with the word ‘desoldering’ if you’ve never desoldered a chip before to see how it works. Also, make sure that the soldering iron is a low-wattage type, and not too hot to avoid lifting the copper traces.

Mcz3001d replacement window screen

A spring loaded solder pump/sucker like this one works best to remove the solder.

Mcz3001d

Close up of IC6501 and IC8002 from bottom of board. Note each IC has two unsoldered pins.

Do NOT solder pins 13 or 17. If you're using a socket, it would be best to clip the legs in those holes off the socket.

Be aware that each chip has two pins are not soldered to the board. This is normal and so don’t try to solder those pins or the fix will not work. Take note of the orientation of the chips since there is a notch on one end facing the closest edge of the board. You do NOT want to install the chips backwards. Also, don’t solder the new chips in directly to the board. Use sockets in case you ever need to do this repair again, since having to unsolder these chips is most of the work. If they were socketed in the first place, you could replace them without having to solder or even having to remove the D board.

I wasn’t sure of the best way to purchase the ICs, since forum participants mentioned purchasing them on Ebay, where there are several China-based vendors offering MCZ3001DB chips but the shipping times from China vary considerably and can take from 10 days to 3 weeks. The vendor I chose was TriState Module because I wanted a U.S.-based company. They sent me a pair of ICs for around $20 including shipping charges. However, they no longer have these parts in stock and they are getting harder to find. I also needed a pair of 18-pin dip sockets which I found at the local Radio Shack for $.59 each. They look like the parts on the left in the image below:

After replacing the ICs with sockets, you’ll need to install the replacement ICs. Odds are that only one of the chips is bad, but since you won’t know which one, it’s best to just replace them both. It is necessary to squeeze the pins together to get the legs aligned with the holes in the sockets. This style of IC has its legs spread out by default, and so they won’t automatically align unless you pre-bend them inward just a little to align with the holes in the socket. Carefully examine the chips after you install them to make sure all the legs made it into the socket and that the little half-circle notch at the end of the chip is facing toward the near edge of the board as shown in the photo below.

After re-installing the board and attaching all the cables, it would be a good idea to test it to make sure the repair worked before reinstalling the cover. If you unlatched the tray and slid the boards back to make access easier, you’ll need to put them back in position or else the remote control and on/off button won’t reach the board. With luck, your TV will be back up and running, avoiding a premature trip to the landfill. I can’t guarantee this fix will work for you, but the consensus on the forums is that it frequently fixes the 6 or 7 blink code problems on the Sony Wega flat screen CRT models.

I found the repair to be of intermediate difficulty, and the result was very gratifying when the TV turned on again. Our TV has now been working like new for more than 2 years, and if it ever happens again, I could fix it more easily thanks to the sockets that are installed. It felt good to resurrect a TV that has great picture and sound quality and, hopefully, a lot of life left in it.

Mcz3001d Replacement Medicare Card

And, in the event it doesn’t work for you, then maybe getting one of those new and improved flat panel TVs is your best alternative. 🙂

[UPDATE 2013-11-15] I mentioned earlier about the difficulty of finding and removing one of the screws under the CRT. Some of these TVs, including the model I repaired, have a set of latches that allow you to release the board and carrier and slide it back about 4″ to make that screw much easier to access. You can see it in the images below:

Mcz3001db

Mcz3001d Datasheet

The D-board and its carrier have latches on both sides that can be lifted to slide the assembly backward about 4 inches.

You may also like:

IC MCZ3001D PDF

60 products offers 60 ic mczd products. About 90% of these are integrated circuits, 1% are transistors. A wide variety of ic mczd options. 63 products offers 63 ic mczd ic products. About 90% of these are integrated circuits. A wide variety of ic mczd ic options are available to. IC MCZD SONY ORIGINAL. IC ICL VOLTAGE DETECTOR 12V(MAX ) (MIN). Product ID: In Stock. Price CA$

Author:Dozshura Daiktilar
Country:Nepal
Language:English (Spanish)
Genre:Health and Food
Published (Last):11 June 2014
Pages:240
PDF File Size:9.77 Mb
ePub File Size:13.37 Mb
ISBN:581-8-43915-385-6
Downloads:58363
Price:Free* [*Free Regsitration Required]
Uploader:Samum

The supplier supports Trade Assurance — A free service that protects your orders from payment to delivery. Relevancy Transaction Level Response Rate.

Sony rear projection SONY power IC MCZ3001D MCZ3001DB MCZ3001DA MCZ3001 good test

Supplier Types Trade Assurance. Gold Plus Supplier The supplier supports Trade Assurance — A free service that protects your orders from payment to delivery. Sample Order Free samples.

Original New IC mczD. We have cooperated with many reliable and powerful agencies for different electronic Brands.

If any quality problems, after our confirmation, we would mccz3001d New and Original ic mczd. New electronics ic mczd. Electronic Components ic mczd new.

20pcs Mczdb Mczd Mcz IC 18 Pin Socket AR | eBay

Massive in stock and fast in delivery 4. Specializing in electronic components distribution.

All Electronics components are original new 1. Quality Warranty Days 5. We are not responsible for any accidents, delays or other issues caused by the express company. The buyer is responsible for all the shipping cost incurred. If the Electronics component is mcz3001e, pls notify us within 3 days of delivery.

MCZDB: ICs & Processors | eBay

Original Mczd New Mczd. Hot sale original new stock MCZD ic components. Electronic Components ic mczd dip We are not responsible for any accidents, delays or other issues caused by the forwarder. If the items are defective, please notify us within 3 days of delivery.

Any items must be returned in their original condition to qualify for a refund or replacement. About product and suppliers: A wide variety of ic mczd ic options are available to you, such as logic ics, mczz3001d ic.

Mcz3001d Replacement Blades

You can also choose from free samples. There are 61 ic mczd ic suppliers, mainly located in Asia. You cmz3001d ensure product safety by selecting from certified suppliers, including 1 with BRC certification.

Mcz3001db

Related Posts